工大CCNP拓扑修改版-Dynamips拓扑配置  工大CCNP拓扑修改版-Dynamips拓扑配置2006-12-13 15:38:07工大CCNP拓扑修改版-Dynamips拓扑配置2006-12-13 15:38:07工大CCNP拓扑修改版-Dynamips拓扑配置 工大的CCNP 那个拓扑只用了1个E口,这样有些小实验,或者想随手验证某个问题时候,那种拓扑不太灵活.我修改了下,增加一个NM-4E模块,这样扩展到4个E口都连到交换机上,这样可以利用网段逻辑分割.同时对一些小实验也能少开点设备.另外的修改就是改成了3620模拟,7200太费资源了.IOS用的应该不是企业版,可能对一些特殊要求不能满足,但满足日常实验足够了.如果非要替换可以自己换个IOS.没有可以兼得的,IOS功能全,内存占就多,机器就受不料.除非有好机器了.我的机器8台全开,CPU在60%左右,PF占用0.98G左右,同比7200时候是降了很多.基本已经不错了,高档点的配置,占的会更少.
拓扑基本一样,就是每个路由器改为4个E口 f0/0 f0/1 f0/2 f0/3都连到交换机上.另外就是取消掉了ATM. 以下是NET文件:
autostart = false
[localhost]
port = 7200
udp = 10000
[[router R1]]
image = D:dy6pre2npdynamipsunzip-c3620-i-mz.122-37.bin
model = 3620
console = 3001
ram = 32
confreg = 0x2142
idlepc = 0x6036ce68
exec_area = 32
mmap = true
slot0=NM-4E
slot1 = PA-4T
f0/0 = SW1 1
f0/1 = SW1 2
f0/2 = SW1 3
f0/3 = SW1 4
s1/1 = R2 s1/0
s1/2 = FR1 1
[[router R2]]
image = D:dy6pre2npdynamipsunzip-c3620-i-mz.122-37.bin
model = 3620
console = 3002
ram = 32
confreg = 0x2142
idlepc = 0x6036ce68
exec_area = 32
mmap = true
slot0=NM-4E
slot1 = PA-4T
f0/0 = SW1 5
f0/1 = SW1 6
f0/2 = SW1 7
f0/3 = SW1 8
s1/1 = R3 s1/0
s1/2 = FR1 2
[[router R3]]
image = D:dy6pre2npdynamipsunzip-c3620-i-mz.122-37.bin
model = 3620
console = 3003
ram = 32
confreg = 0x2142
idlepc = 0x6036ce68
exec_area = 32
mmap = true
slot0=NM-4E
slot1 = PA-4T
f0/0 = SW1 9
f0/1 = SW1 10
f0/2 = SW1 11
f0/3 = SW1 12
s1/1 = R4 s1/0
s1/2 = FR1 3
[[router R4]]
image = D:dy6pre2npdynamipsunzip-c3620-i-mz.122-37.bin
model = 3620
console = 3004
ram = 32
confreg = 0x2142
idlepc = 0x6036ce68
exec_area = 32
mmap = true
slot0=NM-4E
slot1 = PA-4T
f0/0 = SW1 13
f0/1 = SW1 14
f0/2 = SW1 15
f0/3 = SW1 16
s1/1 = R5 s1/0
s1/2 = FR1 4
[1] [2] 下一页
工大CCNP拓扑修改版-Dynamips拓扑配置 工大CCNP拓扑修改版-Dynamips拓扑配置2006-12-13 15:38:07工大CCNP拓扑修改版-Dynamips拓扑配置2006-12-13 15:38:07工大CCNP拓扑修改版-Dynamips拓扑配置 | 
